This file is raw output from pdftotext and may not be ideal for distribution. If you are a maintainer for Hackipedia, please sit down when you have time and clean this text version up. Source PDF: /mnt/main/jmc-storage/docs/DVB/ETSI 300 429 Framing structure, channel coding and modulation for cable systems (1998).pdf Like all conversions the text below should be fully readable as UTF-8 unicode text. --------------------------------------------------------------- EN 300 429 V1.2.1 (1998-04) European Standard (Telecommunications series) Digital Video Broadcasting (DVB); Framing structure, channel coding and modulation for cable systems European Broadcasting Union Union Européenne de Radio-Télévision EBU UER 2 EN 300 429 V1.2.1 (1998-04) Reference REN/JTC-DVB-71 (3z000ioo.PDF) Keywords DVB, digital, video, broadcasting, cable, MPEG, TV ETSI Postal address F-06921 Sophia Antipolis Cedex - FRANCE Office address 650 Route des Lucioles - Sophia Antipolis Valbonne - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88 Internet secretariat@etsi.fr http://www.etsi.fr http://www.etsi.org Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. © European Telecommunications Standards Institute 1998. © European Broadcasting Union 1998. All rights reserved. ETSI 3 EN 300 429 V1.2.1 (1998-04) Contents Intellectual Property Rights................................................................................................................................4 Foreword ............................................................................................................................................................4 1 Scope........................................................................................................................................................5 2 References................................................................................................................................................5 3 Symbols and abbreviations ......................................................................................................................5 3.1 Symbols ............................................................................................................................................................. 5 3.2 Abbreviations..................................................................................................................................................... 6 4 Cable System concept ..............................................................................................................................6 4.1 Baseband interfacing and sync........................................................................................................................... 8 4.2 Sync 1 inversion and randomization .................................................................................................................. 8 4.3 Reed-Solomon (RS) coder ................................................................................................................................. 8 4.4 Convolutional interleaver................................................................................................................................... 8 4.5 Byte to m-tuple conversion ................................................................................................................................ 8 4.6 Differential encoding ......................................................................................................................................... 8 4.7 Baseband shaping .............................................................................................................................................. 8 4.8 QAM modulation and physical interface ........................................................................................................... 8 4.9 Cable receiver .................................................................................................................................................... 8 5 MPEG-2 transport layer ...........................................................................................................................8 6 Framing structure .....................................................................................................................................9 7 Channel coding ......................................................................................................................................10 7.1 Randomization for spectrum shaping............................................................................................................... 10 7.2 Reed-Solomon coding...................................................................................................................................... 11 7.3 Convolutional interleaving............................................................................................................................... 11 8 Byte to symbol mapping ........................................................................................................................12 9 Modulation .............................................................................................................................................13 Annex A (normative): Baseband filter characteristics .....................................................................17 Annex B (informative): Transparency of cable networks ..................................................................18 Annex C (informative): Bibliography...................................................................................................19 History ..............................................................................................................................................................20 ETSI 4 EN 300 429 V1.2.1 (1998-04) Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETR 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available free of charge from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://www.etsi.fr/ipr). Pursuant to the ETSI Interim IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETR 314 (or the updates on http://www.etsi.fr/ipr) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by the Joint Technical Committee (JTC) of the European Broadcasting Union (EBU), Comité Européen de Normalisation ELECtrotechnique (CENELEC) and the European Telecommunications Standards Institute (ETSI). NOTE: The EBU/ETSI JTC was established in 1990 to co-ordinate the drafting of standards in the specific field of broadcasting and related fields. Since 1995 the JTC became a tripartite body by including in the Memorandum of Understanding also CENELEC, which is responsible for the standardization of radio and television receivers. The EBU is a professional association of broadcasting organizations whose work includes the co-ordination of its members' activities in the technical, legal, programme-making and programme-exchange domains. The EBU has active members in about 60 countries in the European broadcasting area; its headquarters is in Geneva *. * European Broadcasting Union CH-1218 GRAND SACONNEX (Geneva) Switzerland Tel: +41 22 717 21 11 Fax: +41 22 717 24 81 Digital Video Broadcasting (DVB) Project Founded in September 1993, the DVB Project is a market-led consortium of public and private sector organizations in the television industry. Its aim is to establish the framework for the introduction of MPEG-2 based digital television services. Now comprising over 200 organizations from more than 25 countries around the world, DVB fosters market- led systems, which meet the real needs, and economic circumstances, of the consumer electronics and the broadcast industry. National transposition dates Date of adoption of this EN: 17 April 1998 Date of latest announcement of this EN (doa): 31 July 1998 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 January 1999 Date of withdrawal of any conflicting National Standard (dow): 31 January 1999 ETSI 5 EN 300 429 V1.2.1 (1998-04) 1 Scope The present document only adds 128 and 256 QAM to the specification. The present document describes the framing structure, channel coding and modulation (denoted "the System" for the purposes of the present document) for a digital multi-programme television distribution by cable. The aim of the present document is to present a harmonized transmission standard for cable and satellite, based on the MPEG-2 System Layer ISO/IEC 13818-1 [1], with the addition of appropriate Forward Error Correction (FEC) technique. This System can be used transparently with the modulation/channel coding system used for digital multi-programme television by satellite (see EN 300 421 [3]). The System is based on Quadrature Amplitude Modulation (QAM). It allows for 16, 32, 64, 128 or 256-QAM constellations. The System FEC is designed to improve Bit Error Ratio (BER) from 10-4 to a range, 10-10 to 10-11, ensuring "Quasi Error Free" (QEF) operation with approximately one uncorrected error event per transmission hour. 2 References References may be made to: a) specific versions of publications (identified by date of publication, edition number, version number, etc.), in which case, subsequent revisions to the referenced document do not apply; or b) all versions up to and including the identified version (identified by "up to and including" before the version identity); or c) all versions subsequent to and including the identified version (identified by "onwards" following the version identity); or d) publications without mention of a specific version, in which case the latest version applies. A non-specific reference to an ETS shall also be taken to refer to later versions published as an EN with the same number. [1] ISO/IEC 13818-1: "Coding of moving pictures and associated audio". [2] IEEE Trans. Comm. Tech., COM-19, pp. 772-781, (October 1971) Forney, G.D.: "Burst- correcting codes for the classic bursty channel". [3] EN 300 421: "Digital Video Broadcasting (DVB); Framing structure, channel coding and modulation for 11/12 GHz satellite services". 3 Symbols and abbreviations 3.1 Symbols For the purposes of the present document, the following symbols apply: α Roll-off factor Ak, Bk Most Significant Bits at the output of the Byte to m-tuple converter f0 Channel centre frequency fN Nyquist frequency g(x) RS code generator polynomial HEX Hexadecimal I Interleaving depth (bytes) I, Q In-phase, Quadrature phase components of the modulated signal j Branch index k Number of bytes mapped into n symbols ETSI 6 EN 300 429 V1.2.1 (1998-04) m Power of 2m-level QAM: 4,5,6,7,8 for 16-QAM, 32-QAM, 64-QAM, 128-QAM, 256-QAM respectively M Convolutional interleaver branch depth for j = 1, M = N/I n Number of symbols mapped from k bytes N Error protected frame length [bytes] p(x) RS field generator polynomial rm In-band ripple (dB) R Randomized sequence Rs Symbol rate corresponding to the bilateral Nyquist bandwidth of the modulated signal Ru Useful bit rate after MPEG-2 transport multiplexer Ru' Bit rate after RS outer coder q Number of bits: 2,3,4,5,6 for 16-QAM, 32-QAM, 64-QAM, 128-QAM, 256-QAM respectively T Number of bytes which can be corrected in RS error protected packet Ts Symbol period 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: BB Baseband BER Bit Error Ratio DTVC Digital Television by Cable FEC Forward Error Correction FIFO First In First Out IF Intermediate Frequency IRD Integrated Receiver Decoder LSB Least Significant Bit MPEG Moving Pictures Experts Group MSB Most Significant Bit MUX Multiplex PDH Plesiochronous Digital Hierarchy PRBS Pseudo Random Binary Sequence QAM Quadrature Amplitude Modulation QEF Quasi Error Free RF Radio Frequency RS Reed-Solomon SMATV Satellite Master Antenna Television TDM Time Division Multiplex TV Television 4 Cable System concept The cable System shall be defined as the functional block of equipment performing the adaptation of the baseband TV signals to the cable channel characteristics (see figure 1). In the cable head-end, the following TV baseband signal sources can be considered: - satellite signal(s); - contribution link(s); - local program source(s). The processes in the following subclauses shall be applied as shown in figure 1. ETSI C a b le H e a d -e n d To R F * C able data C hannel BB Sync1 QAM R eed- C onvol. I Inversion Byte M odulator 8 S olom on 8 Inter- 8 m m & To D ifferential B aseband & P hysic al Random i- leaver m -tuple E ncoding shaping IF cloc k Interfac e Coder zation Conversion Q P hysic al I=12 bytes Interfac e (204,188) Clock & S ync Generator 7 * M P E G -2 tra nspo rt M ux pac kets ETSI C a b le IR D RF I data * Sync1 P hysical Matc hed S ym bol BB m Inversion Interfac e F ilter D ifferential m To 8 C onvol. 8 R eed- 8 8 & & & Byte D einter- S olom on Physic al D ec oder E nergy From R F QA M Q E qualizer M apping leaver D ec oder Interface clock dispersal c able c hannel D em od. R em oval Carrier & C lock & S ync Figure 1: Conceptual block diagram of elements at the cable head-end and receiving site Recovery EN 300 429 V1.2.1 (1998-04) 8 EN 300 429 V1.2.1 (1998-04) 4.1 Baseband interfacing and sync This unit shall adapt the data structure to the format of the signal source. The framing structure shall be in accordance with MPEG-2 transport layer including sync bytes. NOTE: Interfaces are not part of the present document. 4.2 Sync 1 inversion and randomization This unit shall invert the Sync 1 byte according to the MPEG-2 framing structure, and randomizes the data stream for spectrum shaping purposes. 4.3 Reed-Solomon (RS) coder This unit shall apply a shortened Reed-Solomon (RS) code to each randomized transport packet to generate an error- protected packet. This code shall also be applied to the Sync byte itself. 4.4 Convolutional interleaver This unit shall perform a depth I = 12 convolutional interleaving of the error-protected packets. The periodicity of the sync bytes shall remain unchanged. 4.5 Byte to m-tuple conversion This unit shall perform a conversion of the bytes generated by the interleaver into QAM symbols. 4.6 Differential encoding In order to get a rotation-invariant constellation, this unit shall apply a differential encoding of the two Most Significant Bits (MSBs) of each symbol. 4.7 Baseband shaping This unit performs mapping from differentially encoded m-tuples to I and Q signals and a square-root raised cosine filtering of the I and Q signals prior to QAM modulation. 4.8 QAM modulation and physical interface This unit performs QAM modulation. It is followed by interfacing the QAM modulated signal to the Radio Frequency (RF) cable channel. 4.9 Cable receiver A System receiver shall perform the inverse signal processing, as described for the modulation process above, in order to recover the baseband signal. 5 MPEG-2 transport layer The MPEG-2 Transport Layer is defined in ISO/IEC 13818-1 [1]. The Transport Layer for MPEG-2 data is comprised of packets having 188 bytes, with one byte for synchronization purposes, three bytes of header containing service identification, scrambling and control information, followed by 184 bytes of MPEG-2 or auxiliary data. ETSI 9 EN 300 429 V1.2.1 (1998-04) 6 Framing structure The framing organization shall be based on the MPEG-2 transport packet structure. The System framing structure is shown on figure 2. Figure 2: Framing structure ETSI 10 EN 300 429 V1.2.1 (1998-04) 7 Channel coding To achieve the appropriate level of error protection required for cable transmission of digital data, a FEC based on Reed-Solomon encoding shall be used. In contrast to the Baseline System for satellite described in ETS 300 421 [3], no convolutional coding shall be applied to cable transmission. Protection against burst errors shall be achieved by the use of byte interleaving. 7.1 Randomization for spectrum shaping The System input stream shall be organized in fixed length packets (see figure 2), following the MPEG-2 transport multiplexer. The total packet length of the MPEG-2 transport MUX packet is 188 bytes. This includes 1 sync-word byte (i.e. 47HEX). The processing order at the transmitting side shall always start from the MSB (i.e. 0) of the sync word-byte (i.e. 01000111). In order to comply with the System for satellite in ETS 300 421 [3] and to ensure adequate binary transitions for clock recovery, the data at the output of the MPEG-2 transport multiplex shall be randomized in accordance with the configuration depicted in figure 3. The polynomial for the Pseudo Random Binary Sequence (PRBS) generator shall be: 1 + X14 + X15 Loading of the sequence "100101010000000" into the PRBS registers, as indicated in figure 3, shall be initiated at the start of every eight transport packets. To provide an initialization signal for the descrambler, the MPEG-2 sync byte of the first transport packet in a group of eight packets shall be bitwise inverted from 47HEX to B8HEX. Figure 3: Scrambler/descrambler schematic diagram The first bit at the output of the PRBS generator shall be applied to the first bit of the first byte following the inverted MPEG-2 sync byte (i.e.B8HEX). To aid other synchronization functions, during the MPEG-2 sync bytes of the subsequent 7 transport packets, the PRBS generation continues, but its output shall be disabled, leaving these bytes unrandomized. The period of the PRBS sequence shall therefore be 1 503 bytes. The randomization process shall be active also when the modulator input bit-stream is non-existant, or when it is non- compliant with the MPEG-2 transport stream format (i.e. 1 sync byte + 187 packet bytes). This is to avoid the emission of an unmodulated carrier from the modulator. ETSI 11 EN 300 429 V1.2.1 (1998-04) 7.2 Reed-Solomon coding Following the energy dispersal randomization process, systematic shortened Reed-Solomon encoding shall be performed on each randomized MPEG-2 transport packet, with T = 8. This means that 8 erroneous bytes per transport packet can be corrected. This process adds 16 parity bytes to the MPEG-2 transport packet to give a codeword (204,188). NOTE: RS coding shall also be applied to the packet sync byte, either non-inverted (i.e. 47HEX) or inverted (i.e. B8HEX). Code Generator Polynomial: g(x) = (x+λ0)(x+λ1)(x+λ2) ... (x+λ15), where λ = 02HEX Field Generator Polynomial: p(x) = x8 + x4 + x3 + x2 + 1 The shortened Reed-Solomon code shall be implemented by appending 51 bytes, all set to zero, before the information bytes at the input of a (255,239) encoder; after the coding procedure these bytes are discarded. 7.3 Convolutional interleaving Following the scheme of figure 4, convolutional interleaving with depth I = 12 shall be applied to the error protected packets (see figure 2c). This results in an interleaved frame (see figure 2d). The convolutional interleaving process shall be based on the Forney approach (see Burst-correcting codes for the classic bursty channel in IEEE Trans. Comm. Tech., COM-19 [2]) which is compatible with the Ramsey type III approach, with I = 12. The Interleaved Frame shall be composed of overlapping error protected packets and shall be delimited by MPEG-2 sync bytes (preserving the periodicity of 204 bytes). The interleaver may be composed of I = 12 branches, cyclically connected to the input byte-stream by the input switch. Each branch shall be a First In First Out (FIFO) shift register, with depth (Mj) cells (where M = 17 = N/I, N = 204 = error protected frame length, I = 12 = interleaving depth, j = branch index). The cells of the FIFO shall contain 1 byte, and the input and output switches shall be synchronized. For synchronization purposes, the sync bytes and the inverted sync bytes shall be always routed into the branch "0" of the interleaver (corresponding to a null delay). NOTE: The deinterleaver is similar, in principle, to the interleaver, but the branch indexes are reversed (i.e. j = 0 corresponds to the largest delay). The deinterleaver synchronization can be carried out by routeing the first recognized sync byte into the "0" branch. Sync word route Sync word route 0 0 0 0 17x11 1 1 17=M 1 byte per position 2 2 8 8 17x2 1 byte per position 17x3 3 3 9 9 17x3 17x2 10 10 17=M 11 11 = I -1 11 11 = I-1 17x11 FIFO shift register Interleaver I=12 De-interleaver I=12 Figure 4: Conceptual diagram of the convolutional interleaver and de-interleaver ETSI 12 EN 300 429 V1.2.1 (1998-04) 8 Byte to symbol mapping After convolutional interleaving, an exact mapping of bytes into symbols shall be performed. The mapping shall rely on the use of byte boundaries in the modulation system. In each case, the MSB of symbol Z shall be taken from the MSB of byte V. Correspondingly, the next significant bit of the symbol shall be taken from the next significant bit of the byte. For the case of 2m-QAM modulation, the process shall map k bytes into n symbols, such that: 8k=n×m The process is illustrated for the case of 64-QAM (where m = 6, k = 3 and n = 4) in figure 5: NOTE 1: b0 shall be understood as being the Least Significant Bit (LSB) of each byte or m-tuple. NOTE 2: In this conversion, each byte results in more than one m-tuple, labelled Z, Z+1, etc. with Z being transmitted before Z+1. Figure 5: Byte to m-tuple conversion for 64-QAM The two most significant bits of each symbol shall then be differentially coded in order to obtain a π/2 rotation-invariant QAM constellation. The differential encoding of the two MSBs shall be given by the following Boolean expression: 1 61 6 1 61 I k = Ak ⊕ Bk . Ak ⊕ I k −1 + Ak ⊕ Bk . Ak ⊕ Qk −1 6 1 61 6 1 Qk = Ak ⊕ Bk . Bk ⊕ Qk −1 + Ak ⊕ Bk . Bk ⊕ I k −1 61 6 NOTE: For the above Boolean expression " ⊕ " denotes the EXOR function, "+" denotes the logical OR function, "." denotes the logical AND function and the overbar denotes inversion. ETSI 13 EN 300 429 V1.2.1 (1998-04) Figure 6 gives an example of implementation of byte to symbol conversion. Figure 6: Example implementation of the byte to m-tuple conversion and the differential encoding of the two MSBs 9 Modulation The modulation of the System shall be Quadrature Amplitude Modulation (QAM) with 16, 32, 64, 128 or 256 points in the constellation diagram. The System constellation diagrams for 16-QAM, 32-QAM and 64-QAM are given in figure 7. The System constellation diagrams for 128-QAM and 256-QAM are given in figure 8. These constellation diagrams represent the signal transmitted in the cable system. As shown in figure 7, the constellation points in Quadrant 1 shall be converted to Quadrants 2, 3 and 4 by changing the two MSB (i.e. Ik and Qk) and by rotating the q LSBs according to the following rule given in table 1: Table1: Conversion of constellation points of quadrant 1 to other quadrants of the constellation diagram given in figure 7 Quadrant MSBs LSBs rotation 1 00 2 10 + π/2 3 11 +π 4 01 + 3π/2 Receivers shall support at least 64-QAM modulation. ETSI 14 EN 300 429 V1.2.1 (1998-04) 1 6-Q A M 32-Q A M Q Q I kQ k = 1 0 I kQ k = 00 1 01 1 1 1 0 0 1 1 0 0 1 10 00 0 1 0 1011 1001 0010 0011 I kQ k = 10 I kQ k = 00 1 0 01 0 1 01 0 1 1 0 0 0 1 0 0 1 00 0 01 0 1 0 0 1 1 1 1010 1000 0000 0001 1 0 11 0 10 1 0 0 1 0 0 0 0 0 0 0 00 0 00 0 1 0 0 0 1 1 1101 1100 0100 0110 I 1 1 01 1 1 10 0 1 1 1 0 0 0 0 1 0 00 0 11 0 0 01110 1111 1110 0101 0111 I 1 1 11 1 1 11 0 1 1 1 1 0 0 0 1 0 01 0 11 0 1 0 1 0 1 0 I kQ k = 1 1 I kQ k = 0 1 1 10 1 0 1 1 1 1 0 0 1 0 11 0 11 1 1 I kQ k = 11 I kQ k = 01 64-Q A M Q 10 1 1 0 0 1 0 1 1 10 1 0 01 1 0 1 0 0 1 00 0 01 0 0 0 0 0 1 0 01 0 0 1 10 1 00 1 1 0 0 I kQ k = 1 0 I kQ k = 0 0 10 1 1 0 1 1 0 1 1 11 1 0 01 1 1 1 0 0 1 01 0 01 0 1 0 00 1 0 1 1 0 0 1 11 1 0 01 1 1 0 10 1 0 0 1 1 0 1 0 11 1 0 00 1 1 1 0 0 0 01 0 00 0 1 0 00 0 0 1 1 0 0 0 11 1 0 00 1 1 0 10 1 0 0 0 1 0 1 0 10 1 0 00 1 0 1 0 0 0 00 0 00 0 0 0 00 0 0 0 1 0 0 0 10 1 0 00 1 0 0 11 0 1 0 0 1 1 0 10 1 1 1 00 0 1 1 1 0 0 00 0 10 0 0 0 0 1 0 0 10 0 1 1 01 0 01 1 0 0 0 I 11 0 1 1 0 1 1 0 11 1 1 1 00 1 1 1 1 0 0 10 0 10 0 0 1 0 1 0 0 11 0 1 1 01 1 01 1 0 0 1 11 1 1 1 0 1 1 1 11 1 1 1 10 1 1 1 1 1 0 10 0 10 1 0 1 0 1 0 11 1 0 1 11 1 1 01 1 1 0 1 I kQ k = 1 1 I kQ k = 0 1 11 1 1 0 0 1 1 1 10 1 1 1 10 0 1 1 1 1 0 00 0 10 1 0 0 0 1 0 1 10 0 1 1 11 0 01 1 1 0 0 I k Q k a re th e tw o M SB s in e ac h q u a d ra n t Figure 7: Constellation diagrams for 16-QAM, 32-QAM and 64-QAM ETSI 15 EN 300 429 V1.2.1 (1998-04) 256 QAM Figure 8: Constellation diagrams for 128-QAM and 256-QAM ETSI 16 EN 300 429 V1.2.1 (1998-04) Prior to modulation, the I and Q signals shall be square-root raised cosine filtered. The roll-off factor shall be 0,15. Examples of transparent cable transmissions are given in table B.1. The square-root raised cosine filter shall have a theoretical function defined by the following expression: H ( f ) = 1 for f < f N (1 − α ) 1 1 1 π  f − f  2    + sin  N  H(f) = 2 2 2fN  α  for f N (1 − α ) ≤ f ≤ f N (1 + α )     H(f) = 0 for f > f N (1 + α ) where 1 R fN = = s is the Nyquist frequency and roll-off factor α = 0,15. 2 Ts 2 The transmitter filter characteristic is given in annex A. ETSI 17 EN 300 429 V1.2.1 (1998-04) Annex A (normative): Baseband filter characteristics The template given in figure A.1 shall be used as a minimum requirement for hardware implementation of the Nyquist filter. This template takes into account not only the design limitations of the digital filter, but also the artefacts coming from the analogue processing components of the System (e.g. D/A conversion, analogue filtering, etc.). The value of in-band ripple rm in the pass-band up to 0,85 fN as well as at the Nyquist frequency fN shall be lower than 0,4 dB. The out-band rejection shall be greater than 43 dB. The filter shall be phase linear with the group delay ripple ≤ 0,1 Ts (ns) up to fN where, Ts = 1/Rs is the symbol period. NOTE: The values for in-band ripple and out of band rejection given in this annex are subject to further study. Figure A.1: Half-Nyquist baseband filter amplitude characteristics ETSI 18 EN 300 429 V1.2.1 (1998-04) Annex B (informative): Transparency of cable networks In order to achieve a transparent re-transmission of different services on cable systems, the limitations imposed by the System for cable transmission in 8 MHz cable channel bandwidth should be taken into account. With a roll-off factor of 0,15, the theoretical maximum symbol rate in an 8 MHz channel is 6,96 MBaud. Table B.1 of this annex gives examples of the wide range of possible cable symbol rates and occupied bandwidths for different useful bit rates considering 16-QAM, 32-QAM and 64-QAM constellations. For full transparency, the same useful bit rate (excluding RS coding) should be used on the contributing system and the cable network for secondary distribution. In the upper part of table B.1, an example of a transparent transmission of the satellite rate of 38,1 Mbit/s, which may be potentially used by many existing satellites (EN 300 421 [3]), is given. This bit rate can be re-transmitted very efficiently in an 8 MHz cable channel by using 64-QAM. A bit rate compatible with terrestrial Plesiochronous Digital Hierarchy (PDH) networks can be re-transmitted in an 8 MHz channel by using 32-QAM. As shown in the lower part of table B.1, network performance limitations, service requirements (e.g. additional data/audio services), characteristics of the primary distribution system (e.g. satellite, fibre) or other constraints may lead to different usages of the System to appropriately suit various applications. NOTE: Examples of satellite useful bit rates Ru are taken from EN 300 421 [3]. Table B.1: Examples of useful bit rates Ru and total bit rates Ru' for transparent re-transmission and spectrum efficient use on cable networks Useful bit rate Ru Total bit rate Ru' Cable symbol rate Occupied Modulation (MPEG-2 transport layer) incl. RS(204,188) bandwidth scheme [Mbit/s] [Mbit/s] [MBaud] [MHz] 38,1 41,34 6,89 7,92 64-QAM 31,9 34,61 6,92 7,96 32-QAM 25,2 27,34 6,84 7,86 16-QAM 31,672 PDH 34,367 6,87 7,90 32-QAM 18,9 20,52 3,42 3,93 64-QAM 16,0 17,40 3,48 4,00 32-QAM 12,8 13,92 3,48 4,00 16-QAM 9,6 10,44 1,74 2,00 64-QAM 8,0 8,70 1,74 2,00 32-QAM 6,4 6,96 1,74 2,00 16-QAM ETSI 19 EN 300 429 V1.2.1 (1998-04) Annex C (informative): Bibliography For the purposes of the present document, the following informative references apply: - DTVB 1190/DTVC 38, 3rd revised version, February 1994 (Contribution from DTVC), document: "Specification of modulation, channel coding and framing structure for the Baseline System for digital multi- programme television by cable". - DTVB 1110/GT V4/MOD 252/ DTVC 18, 7th revised version, January 1994 (Contribution from V4/MOD-B), document: "Specification of the "Baseline modulation/channel coding system" for digital multi-programme television by satellite". - DVB-TM 1189/DTVC 37 (Contribution from Task Force DTVC), document: "Potential applications of the System for Digital multi-programme Television by Cable". - GT V4/MOD 247 document, Jézéquel, P.Y., Veillard, J: "Introduction of Digital Television in cable networks". - Reimers, U. NAB'93, document GT V4/MOD 249: "The European perspectives on Digital Television Broadcasting". ETSI 20 EN 300 429 V1.2.1 (1998-04) History Document history Edition 1 December 1994 Publication as ETS 300 429 V1.1.2 August 1997 Publication V1.2.1 December 1997 One-step Approval Procedure OAP 9815: 1997-12-12 to 1998-04-10 V1.2.1 April 1998 Publication ISBN 2-7437-2141-3 Dépôt légal : Avril 1998 ETSI